MPGeneral trading · UAE & GCC
Industrial pumps supplier in the UAE and GCC
Centrifugal, multistage, submersible, slurry, sewage, dosing and other industrial pumps for oil and gas, mining, water and plant duties, supplied to your duty point and specification.
Pump types we supply
| Pump type | Typical use | What to tell us |
|---|---|---|
| Centrifugal pumps (end suction, split case, inline) | Water, process and transfer duties; cooling water; general plant service | Fluid, flow, head, temperature and materials |
| Multistage and booster pumps | Pressure boosting, water supply, reverse osmosis feed, high-head duties | Flow, discharge pressure and number of pumps (duty and standby) |
| Vertical turbine and sump pumps | Tanks, sumps, wells and cooling water intake | Liquid level, pump length, flow and head |
| Submersible pumps (dewatering, borehole) | Dewatering of excavations and mines, boreholes, drainage | Flow, head, solids content and power supply |
| Sewage and cutter pumps | Sewage lift stations, wastewater and effluent | Flow, head and the maximum solids size to pass |
| Slurry pumps | Mining, tailings, dredging and abrasive slurries | Solids type, concentration, particle size, flow and head |
| Chemical process pumps | Acids, alkalis and solvents in process plants | Chemical, concentration, temperature and seal type (sealed or magnetic drive) |
| Positive displacement pumps (gear, screw, progressive cavity) | Oil, fuel, lubricants, viscous liquids and sludge | Fluid, viscosity, flow and pressure |
| Diaphragm and dosing pumps | Chemical dosing, water treatment, drum and sump transfer | Chemical, dosing rate and pressure |
| High-pressure plunger and test pumps | Pressure testing, injection and washing duties | Working pressure, flow and fluid |
| Fire water pumps | Fire pump sets for buildings and plants | Flow, pressure, driver type and the standard your authority requires |
Need a pump that is not listed? Send us the duty and we will confirm what we can quote.
Where these pumps are used in the GCC
| Sector | Typical duties |
|---|---|
| Oil and gas | Process and transfer, produced water, firewater, chemical injection and dosing, fuel and lube oil transfer |
| Mining | Dewatering, slurry and tailings, process water and sump drainage |
| Water and wastewater | Booster sets, sewage lift stations, treatment plant feed and dosing, desalination feed |
| Construction and buildings | Water supply boosting, drainage, sump pumps and fire pump sets |
| Industrial plants | Cooling water, circulation, process chemicals and washdown |
How we quote a pump
Pumps are selected on duty, not on name. We need the flow, the total head, the fluid and its temperature to match a pump to your requirement. We quote from the manufacturers we work with and send the datasheet and performance curve with the offer, so your engineer can check the duty point before you order. If your project calls for a specific standard, such as API 610 for oil and gas process pumps, ISO 5199 or ASME B73.1 for chemical pumps, or NFPA 20 for fire pumps, tell us when you enquire and we will confirm what can be offered before we quote.
Materials and seals
The pump materials must suit the fluid. Cast iron suits clean water, while stainless steel, duplex or high-chrome alloys are used for seawater, chemicals and abrasive slurries. Tell us the fluid and its temperature, and for process pumps the seal arrangement you need, such as a single mechanical seal, a double seal or a sealless design.
Drivers, hazardous areas and spares
We can quote pumps with electric motors to your voltage and frequency, with diesel engine drives for fire water and remote duties, or as bare shaft pumps. For hazardous areas, give us the zone and gas group so the motor can be quoted with a suitable explosion-protection rating. We can also quote spare parts and mechanical seals, bearings and motors for pumps you already run.
What to include in your enquiry
- Pump type and the application
- Fluid, its temperature, and any solids, with the maximum solids size
- Flow rate and total head, or discharge pressure
- Suction conditions: flooded or lift, and the liquid level
- Number of pumps, and whether you need duty and standby
- Driver and power supply: voltage, frequency, and hazardous-area rating if needed
- Materials, seal type and the standard or specification required
- Datasheet or performance curve requirements, and the delivery location
Frequently asked questions
Do you supply pumps for oil and gas?
Yes. Send us the duty, the fluid and the specification, including any API standard your project requires, and we will confirm what we can offer before we quote.
Can you supply pumps for mining and dewatering?
Yes. We quote submersible dewatering pumps and slurry pumps. For slurry, tell us the solids type, concentration and particle size so the pump can be matched to the wear.
What do you need to quote a pump?
The pump type or application, the fluid, the flow rate, the total head, and the power supply. A nameplate photo or an existing datasheet also works if you are replacing a pump.
Do you send a datasheet and performance curve?
Yes. We send the datasheet and the performance curve with the quotation so your engineer can check the duty point.
Do you supply pumps to countries outside the UAE?
Yes. We supply pumps as materials across the UAE and the GCC, delivered with the documentation.
Start a quotation
Have an MR, BOQ or equipment list?
Send it to us and we will come back with a priced quotation and lead times.